Search found 12 matches
- Thu May 21, 2015 3:03 pm
- Forum: X10, A10 Xanura Marmitek Forum
- Topic: Is it possible to use the value of a variable in an email
- Replies: 1
- Views: 6463
Is it possible to use the value of a variable in an email
Hello, i'm using a Eaton Homecontrolbox with firmware 1.6. My question is, can i use the value of a variable in the subject of textbody of an emailmessage ?
- Sun Feb 22, 2015 2:57 pm
- Forum: X10, A10 Xanura Marmitek Forum
- Topic: Firmware files voor HCB
- Replies: 9
- Views: 14760
Firmware files voor HCB
Heeft iemand toevallig nog firmware files beschikbaar voor de HCB, bijv. 1.4.18 en 1.6.0-1026 ? Heb 3, 4 jaar geleden mijn HCB geupgrade naar 1.6, en nooit geen problemen mee gehad. Echter onlangs een IMX10 (eigenlijk Marmitek TWM4) aan mijn installatie toegevoegd, en probeer deze te programmeren ma...
- Thu Dec 22, 2011 12:49 pm
- Forum: X10, A10 Xanura Marmitek Forum
- Topic: Fans of WTW (heat recovery) defect by SAIX?
- Replies: 5
- Views: 7247
Re: Fans of WTW (heat recovery) defect by SAIX?
Henk, Can the sensing feature cause fluctuation of the current of the output ? The fan is not directly switched by the SAIX, there is some electronic between. See also the manual of the heat recovery http://www.xillycom.com/611196_Optieprint_sept2004.pdf, page 16 (perilex aansluiting). So the output...
- Wed Dec 21, 2011 11:01 am
- Forum: X10, A10 Xanura Marmitek Forum
- Topic: Fans of WTW (heat recovery) defect by SAIX?
- Replies: 5
- Views: 7247
Re: Fans of WTW (heat recovery) defect by SAIX?
Henk, I installed the SAIX12 according to the manual on the bwired site http://www.bwired.nl/images/how/xanura_stappenplan.pdf, page 19. Except i don't use L2 (medium fan speed), and i also don't use any switches. When lights are on in the toilet of bathrooms the SAIX12 activates L3 and causes a hig...
- Tue Dec 20, 2011 1:07 pm
- Forum: X10, A10 Xanura Marmitek Forum
- Topic: Fans of WTW (heat recovery) defect by SAIX?
- Replies: 5
- Views: 7247
Fans of WTW (heat recovery) defect by SAIX?
The fans of my WTW installation, a Brinks Renovent Large, broke a couple of times. The mechanic of Brinks told me that possible the SAIX12 i use to toggle between low and high fan speed could cause the problem. This because the fans seems to variate in speed by an external factor. Has anyone experie...
- Sat Nov 21, 2009 11:50 pm
- Forum: X10, A10 Xanura Marmitek Forum
- Topic: How to program a RFIX35 with a letter code
- Replies: 2
- Views: 3579
How to program a RFIX35 with a letter code
i read the manual, but in then manual there isn't a word written about how to program the RFIX35 by the HCB. It is mentioned in the manual that you can program the RFIX35 with het HCB, but how to do that is not noted. Some help would be fine
- Sat Nov 21, 2009 11:02 pm
- Forum: X10, A10 Xanura Marmitek Forum
- Topic: How to program a RFIX35 with a letter code
- Replies: 2
- Views: 3579
How to program a RFIX35 with a letter code
I am trying to program my RFIX35 with the letter Code A. My XanuraHome dealer told me i can program the RFIX35 via the A10-Status page of my HCB. But i can't find a option to send the setup commands on that page. Can anyone give me some advise how to program RFIX35 or how to send setup commands via ...
- Sat Nov 21, 2009 10:04 pm
- Forum: X10, A10 Xanura Marmitek Forum
- Topic: Howto send dim commands with IMX10 to a DAX4
- Replies: 3
- Views: 4338
Howto send dim commands with IMX10 to a DAX4
ok, tryed tbat and its working fine, thx for your advise Bastiaan.
- Sat Nov 21, 2009 9:29 pm
- Forum: X10, A10 Xanura Marmitek Forum
- Topic: Howto send dim commands with IMX10 to a DAX4
- Replies: 3
- Views: 4338
Howto send dim commands with IMX10 to a DAX4
no, is that the trick, putting them on the same address ?
- Thu Nov 19, 2009 11:24 pm
- Forum: X10, A10 Xanura Marmitek Forum
- Topic: Howto send dim commands with IMX10 to a DAX4
- Replies: 3
- Views: 4338
Howto send dim commands with IMX10 to a DAX4
Hello, i installed a IMX10 in combination with a 1-vlaks impulsdrukker (don't know the english words). Now i like to send on-off and dim commands from the IMX10 to a DAX4. I programmed the IMX10 with the option 'Impulsdrukker 1-vlaks (dimmen)'. Futher i made macro's which send on or off commands to ...
- Sun Jun 14, 2009 4:33 pm
- Forum: X10, A10 Xanura Marmitek Forum
- Topic: Problems with brand new HCB
- Replies: 2
- Views: 3739
Problems with brand new HCB
The problem was caused by a bad flash. I returned the HCB to the shop and got a new one. This one works fine )
- Sun May 24, 2009 11:42 pm
- Forum: X10, A10 Xanura Marmitek Forum
- Topic: Problems with brand new HCB
- Replies: 2
- Views: 3739
Problems with brand new HCB
Yesterday my new HCB arrived. Connected the HCB with the yellow cable on my router, plugged the power cable in, grabbed the ip adres on my dhcp server, typed the ip adres in my browser. The homepage of my HCB is loaded, but stays loading "Loading HCB Application Software" and further nothi...