Search found 7 matches
- Mon Jun 27, 2016 10:03 pm
- Forum: Opentherm Gateway Forum
- Topic: MQTT - Authentication
- Replies: 6
- Views: 5429
Re: MQTT - Authentication
We solved it then. It never occurred to me that the otmonitor.conf is written by otmonitor, so yes the password in my config file was unencrypted. When i 'save' the otmonitor.conf by otmonitor i get an encrypted password which works as expected when i turn on the authentication on mosquitto.. Thanks...
- Sat Jun 25, 2016 7:33 am
- Forum: Opentherm Gateway Forum
- Topic: MQTT - Authentication
- Replies: 6
- Views: 5429
Re: MQTT - Authentication
Lots more logs, just trying to supply a lot of info. First, all the logs of when it goes wrong.. WITH authentication. As you can see, the otmonitor user exists and it works with mosquitto_sub. pi@zonnestroom:~ $ mosquitto_sub -d -t '$SYS/broker/load/bytes/sent/1min' -v -h 192.168.153.1 -u otmonitor ...
- Fri Jun 24, 2016 2:50 pm
- Forum: Opentherm Gateway Forum
- Topic: MQTT - Authentication
- Replies: 6
- Views: 5429
Re: MQTT - Authentication
mosquitto.conf pid_file /var/run/mosquitto.pid persistence true persistence_location /var/lib/mosquitto/ log_dest file /var/log/mosquitto/mosquitto.log password_file /etc/mosquitto/passwd allow_anonymous false log_type all There is not much info in it. The 192.168.153.7 is a PI which runs the otmoni...
- Thu Jun 23, 2016 11:46 am
- Forum: Opentherm Gateway Forum
- Topic: MQTT - Authentication
- Replies: 6
- Views: 5429
MQTT - Authentication
Hello, I'm trying to connect my OTmonitor to a MQTT bus (mosquitto). When i configure mosquitto to use NO AUTHENTICATION it works like a charm, however when i wish to use authentication to message are not sent to mosquitto. My username/password combination is correct, since when i use mosquitto_pub/...
- Thu Jan 07, 2016 8:05 am
- Forum: Opentherm Gateway Forum
- Topic: OTGW stopped working, many Error 03s
- Replies: 10
- Views: 10853
Re: OTGW stopped working, many Error 03s
I'll hook the OTGW up again today to test with a different voltage setting.
Before i do that can you explain why i need a different voltage setting? It's been running fine for weeks on setting 3 (default), why would it suddenly need a different voltage setting?
Before i do that can you explain why i need a different voltage setting? It's been running fine for weeks on setting 3 (default), why would it suddenly need a different voltage setting?
- Wed Jan 06, 2016 12:55 pm
- Forum: Opentherm Gateway Forum
- Topic: OTGW stopped working, many Error 03s
- Replies: 10
- Views: 10853
OTGW stopped working, many Error 03s
Hello, I have a simple setup. iSense v28, OTGW 4.2.5, Remeha Avanta. The OTGW is hooked up to a rPI through USB. The rPI runs the otmonitor software and has been running fine for weeks, until about 3 days ago. When i 'view' the messages tab, all i see are Error 03. When i switch the OTGW to monitor ...
- Mon Nov 09, 2015 4:57 pm
- Forum: Opentherm Gateway Forum
- Topic: Opentherm Gateway
- Replies: 338
- Views: 329196
Re: Opentherm Gateway
I've been trying to get the otmonitor to run on a RaspberryPI with Raspian Jessie. I'm using the following command to run it: ./otmonitor-ahf -w 8080 --daemon /dev/ttyUSB0 It starts and i can see the webpages, however they do not get updated with any values. I know my OTGW is on ttyUSB0, since i can...