Home Automation Domotica Forum Europe, Bwired Forum

I followed the handout allready...., but used the low power variant...

Should it also be visible in the homeseer log? (when switching the led within Homeseer....)

I tried using the "normal" variant, but was not able (jet) to get it working

i think that i have another sketch.... on line 709 to 731 it says: void loop() { #if SERIAL || DEBUG Serial.print('#'); delay(2); #endif #if PIR_PORT if (pir.triggered()) { payload.moved = pir.state(); #if SERIAL || DEBUG delay(2); // without this delay, reception is garbage... Serial.print("PI...

I got the Jeenode and the roomboard working for a while now. In the sketch there is also a LED defined. It switches on when a movement is detected from the PIR. In the Homeseer "plugin" there are buttons aside the device which could indicate that it is possible to switch the LED on/off... ...

Thanks jcw,

That could explain that when i connect the jeenode and the bridgeboard, and power it via the bridgeboard works. And not working when connecting the jeenode and the aa board...

with roomnode i meant the jeenode and the roomboard, powered by an external batterypack (3 times AA) When i switch the external batterypack for the AA board, it doesn't work anymore.... On the AA board there is SJ1 solderjoint. Als when i use another jeenode and the bridgeboard, i have problems with...

next question......:
The roomnode works with an external battery, but not with the AA Board as displayed on the photo from Digit...
The voltage measures ok on the AA board and on the JeeNode...

There are solderjoints on the board, but it seems they are not that well documented...?

if all things where that easy....
But why was it giving correct values with another sketch? (connected via USB)

I followed the "manual" for the Homeseer Intergration of Jeenode. In the homeseer log i see values: 4-12-2010 15:01:56 JeeData 5,1,4,1,0,2,Off ,0,On ,1, 4-12-2010 15:01:56 JeeData processDevValues 4-12-2010 15:01:56 JeeData Off 0On 1 4-12-2010 15:02:57 JeeData 5,2,0,0,0,-396,0, But the tem...

Received my new RF12 module today: work right after soldering.....

Thanks jcw!!!

nee: geen error 404 melding in IE8
Je pdf link werkt wel, dank je

De matrix geeft een rood kruisje....

Ik heb besloten om een Jeelink er extra bij te bestellen.
Bestelling is zojuist gedaan

small test:

i desoldered the RF12 module from the not working jeenode.
When i then connect the jeenode to the system i am able tho change the frequency, eventhough the RF12 module is not precent.....

It seems that the RF12 module is defective.....

I attendet the workshop yesterday, great workshop!!! Yesterday i allready had some trouble with mij Jeenode. I could not see any output with de serial monitor and the RF12demo loaded, nor could i give a command (ie 8b change from 433 to 868 Mhz). Jean Claud had a look at the setup and could not find...

Dus als ik de extra dataopslag van de JEElink niet nodig niet nodig heb kan ik beter de Jeenode USB hebben?
Voor de werking van het RF gedeelte maakt het niets uit?

Erg jammer dat we niet toegekomen zijn aan de integratie met Homeseer en het RF gedeelte...

sorry, helaas: ik niet.....

Even een vraagje aan de geleerden:
Is de J-Node USB v3 een "opgevoerde" Jeelink V2?
maw:
Kan ik met de J-node v3 een netwerk opbouwen met bv de J5?
Het voordeel zou dan nl zijn dat ik ook i/o poorten heb bij mijn server