Firmware files voor HCB

Forum about Xanura, Eaton Holec and Marmitek and other brand X10 and A10 devices.

Firmware files voor HCB

Postby tsiis » Sun Feb 22, 2015 1:57 pm

Heeft iemand toevallig nog firmware files beschikbaar voor de HCB, bijv. 1.4.18 en 1.6.0-1026 ? Heb 3, 4 jaar geleden mijn HCB geupgrade naar 1.6, en nooit geen problemen mee gehad. Echter onlangs een IMX10 (eigenlijk Marmitek TWM4) aan mijn installatie toegevoegd, en probeer deze te programmeren maar zonder resultaat. Las elders op dit forum dat dit een bekend probleem is met 1.6. Mijn plan is de HCB te downgraden naar 1.4, de IMX te programmeren, en daarna de HCB weer te upgraden naar 1.6.

Kan echter nergens de firmware files meer vinden op internet. Dus vandaar mijn verzoek. Als je een andere oplossing hebt voor mijn probleem dan hoor ik dat graag.
tsiis
Starting Member
Starting Member
 
Posts: 12
Joined: May 2009
Location: Netherlands

Re: Firmware files voor HCB

Postby Henk » Mon Feb 23, 2015 8:08 am

No way to go back to 1.4 firmware and not needed

Check the documentation of the IMX10
Write down the required X10 commands sequence for each switch and what kind of feedback of the blinking led of the module
Use the HCB to issue each command mannual or use a Marmitex remote X10 controller and check the blinking led .....

Alternative you may write a HCB macro with all the X10 commands with time delays in it (it may not work because of issueing multi commands to the same module it may overwrite itself - i should have a check by myself ) .... put the module in programming mode and execute the macro and watch the feedback of the blinking led

Henk
Henk
Member
Member
 
Posts: 450
Joined: May 2006
Location: Netherlands

Re: Firmware files voor HCB

Postby RDNZL » Wed Oct 21, 2015 6:11 pm

Does anyone has one or more of the older firmware files for HCB? (Home Control Box)
HCB_firmware_eh_1.6.0_1025.zip
HCB_FW_1.6.zip
firmware-eh_1.4.15-983.zip

Something to investigate.. Thanks! :D
Regards, Ron.
User avatar
RDNZL
Forum Moderator
Forum Moderator
 
Posts: 994
Joined: September 2006
Location: Dordrecht, The Netherlands

Re: Firmware files voor HCB

Postby Bwired » Wed Oct 21, 2015 9:53 pm

ask these guys
http://www.quby.nl/
Arjen Noorbergen is the maker of the HCB, he can help you with those files I think
User avatar
Bwired
Administrator
Administrator
 
Posts: 5305
Joined: March 2006
Location: Netherlands

Re: Firmware files voor HCB

Postby RDNZL » Fri Oct 23, 2015 5:13 pm

Sure I could do that, if they had a working contact form on their website :x
Anyone who had a HCB in the past please do a search on your NAS for one of the files above...
Regards, Ron.
User avatar
RDNZL
Forum Moderator
Forum Moderator
 
Posts: 994
Joined: September 2006
Location: Dordrecht, The Netherlands

Re: Firmware files voor HCB

Postby Bwired » Fri Oct 23, 2015 8:07 pm

I see a contactform :-)
but I send a tweet to Arjan, I hope he can help
User avatar
Bwired
Administrator
Administrator
 
Posts: 5305
Joined: March 2006
Location: Netherlands

Re: Firmware files voor HCB

Postby RDNZL » Sat Oct 24, 2015 10:42 am

The three time I tried the form didn't work, that's why I said *working* contact form. :wink:
Thanks for the tweet, my google skills didn't seem to help.
Regards, Ron.
User avatar
RDNZL
Forum Moderator
Forum Moderator
 
Posts: 994
Joined: September 2006
Location: Dordrecht, The Netherlands

Re: Firmware files voor HCB

Postby arjenn » Sat Oct 24, 2015 12:47 pm

Gee, that has been a while. .. I am not sure if we could still find that. But I'll ask around in the office on Monday.

Curious what you would need it for


Arjen
Quby
arjenn
Starting Member
Starting Member
 
Posts: 1
Joined: October 2015


Re: Firmware files voor HCB

Postby RDNZL » Sat Oct 24, 2015 8:16 pm

Thanks a lot Peter!
Regards, Ron.
User avatar
RDNZL
Forum Moderator
Forum Moderator
 
Posts: 994
Joined: September 2006
Location: Dordrecht, The Netherlands


Return to X10, A10 Xanura Marmitek Forum

Who is online

Users browsing this forum: No registered users and 1 guest