Fritzbox CLI
Fritzbox CLI
Since few days I have lost CLI on the Fritzbox
Can't find any setting about CLI.
Only option that i can change is the region. this one is set on Netherlands.
Is this a local problem or a Ziggo problem..?
CLI did work fine in the last years on the Fritzbox
Can't find any setting about CLI.
Only option that i can change is the region. this one is set on Netherlands.
Is this a local problem or a Ziggo problem..?
CLI did work fine in the last years on the Fritzbox
Enver Tanriverdi | http://blog.tane.nl
Re: Fritzbox CLI
Update:
Almost every option of the phone part is turned on/off.
No succes
Ziggo checked all the settings..it must work all is correct.
What are the regional settings that most of you use on the fritz?
Som post suggested to select German...did not help.
I'm going to upload another firmware..hope this will help
Almost every option of the phone part is turned on/off.
No succes
Ziggo checked all the settings..it must work all is correct.
What are the regional settings that most of you use on the fritz?
Som post suggested to select German...did not help.
I'm going to upload another firmware..hope this will help
Enver Tanriverdi | http://blog.tane.nl
Re: Fritzbox CLI
Old topic update:
It's about a year ago that my Fritzbox is not showing any CLI info.
CLI will work fine when using normal dect set.
Anyone else having the same problem with ziggo and fritzbox?
It's about a year ago that my Fritzbox is not showing any CLI info.
CLI will work fine when using normal dect set.
Anyone else having the same problem with ziggo and fritzbox?
Enver Tanriverdi | http://blog.tane.nl
Re: Fritzbox CLI
Enver,
I have a Fritzbox 7390 with Ziggo and no problems with CLI on the Dect phones.
Mind you, I use the Fritz!Fon dect phones around the house and I don't have the 7390 hooked into Homeseer (yet).
Regional settings are set to Netherlands.
Firmware was just updated last week. Version: 84.05.06
Hope it helps..
Olof
I have a Fritzbox 7390 with Ziggo and no problems with CLI on the Dect phones.
Mind you, I use the Fritz!Fon dect phones around the house and I don't have the 7390 hooked into Homeseer (yet).
Regional settings are set to Netherlands.
Firmware was just updated last week. Version: 84.05.06
Hope it helps..
Olof
Re: Fritzbox CLI
Olaf,
Thanks..
Ziggo Modem is the Arris.
Fritzbox 7270 firmware 54.05.06
I have checked all the settings including replacement of the special Fritzbox y-cable.
Support from AVM and Ziggo did not solve the problem.
AVM is sending the standaard check list..conclusion was replace your dect handset with FritzPhone... I don't see the CLI on the Fritzbox..
Ziggo is advising remove an add the dects again...
Thanks..
Ziggo Modem is the Arris.
Fritzbox 7270 firmware 54.05.06
I have checked all the settings including replacement of the special Fritzbox y-cable.
Support from AVM and Ziggo did not solve the problem.
AVM is sending the standaard check list..conclusion was replace your dect handset with FritzPhone... I don't see the CLI on the Fritzbox..
Ziggo is advising remove an add the dects again...
Enver Tanriverdi | http://blog.tane.nl
Re: Fritzbox CLI
Hi Tane,
I have Ziggo with Fritz!box, CLI is working as it should. Recently I replaced my 7170 with a 7390 and also on this one CLI is working. I have had some problems with CLI, e.g. when I initially installed the 7390 and changed the country setting once to an other country and afterwards back to NL it didn't work any more. After the following actions:
1) factory reset fritz!box
2) incoming call direct after reboot (CLI is already shown in fritz!box if)
3) configure country settings to NL
CLI works fine.
I have Ziggo with Fritz!box, CLI is working as it should. Recently I replaced my 7170 with a 7390 and also on this one CLI is working. I have had some problems with CLI, e.g. when I initially installed the 7390 and changed the country setting once to an other country and afterwards back to NL it didn't work any more. After the following actions:
1) factory reset fritz!box
2) incoming call direct after reboot (CLI is already shown in fritz!box if)
3) configure country settings to NL
CLI works fine.
Bernard
Re: Fritzbox CLI
No succes...
Will try with another Fritzbox before a buy a new one.
Will try with another Fritzbox before a buy a new one.
Enver Tanriverdi | http://blog.tane.nl
Re: Fritzbox CLI
Installed a 7360 (xs4all) for testing.
CLI is working again..
I have order an new Fritzbox 7390 this one will replace my old fritzbox and the Cisco E4200 what is dropping wifi connections all the time.
CLI is working again..
I have order an new Fritzbox 7390 this one will replace my old fritzbox and the Cisco E4200 what is dropping wifi connections all the time.
Enver Tanriverdi | http://blog.tane.nl
Re: Fritzbox CLI
update the 7390 did not work well.
CLI was missing in 95% of the call's
I contacted AVM today.
They did now about this problem and asked me to install the lab version of the firmware.
After the upgrade Fritz 7390 is working fine including the Homeseer plugin from Digit.
CLI was missing in 95% of the call's
I contacted AVM today.
They did now about this problem and asked me to install the lab version of the firmware.
After the upgrade Fritz 7390 is working fine including the Homeseer plugin from Digit.
Enver Tanriverdi | http://blog.tane.nl