ZonOpToon alternative

Forum about Toon hardware, both versions 1 and 2 of Toon

Moderator: marcelr

Re: ZonOpToon alternative

Postby Cctl01 » Sat Nov 10, 2018 1:55 pm

Sorry for the double posting but I already found the answer to my question here.
https://www.domoticaforum.eu/viewtopic.php?t=11587

Would in your opinion the next best solution be to create a tile that displays the p1 reading and solar out from Domoticz?
I have everything setup there, I'm just looking for a nifty way to display the readings on Toon.
Cctl01
Starting Member
Starting Member
 
Posts: 12
Joined: November 2018

Re: ZonOpToon alternative

Postby madpatrick » Fri Nov 23, 2018 4:45 pm

TerrorSource wrote:Hi guys,

I found an interesting way to do the ZonOpToon cheaper then the usual way.
Someone pointed me to the KWH1073PRO fuse box module, as a replacement for an official ZonOpToon fuse box module.
shop1: https://mdhelektroshop.nl/dmmetering-kw ... p-u-mid-23
shop2: https://www.installatievakwinkel.nl/ine ... kwh1073pro (slightly cheaper)

1. Buy it
2. Put it in the fuse box
3. Connect 1 analog wire to the module and the meteradapter
4. change the value's of "SolarDisplay" and "SolarActivated" in scsync.xml in 1 (instead of 0)
5. Reboot the toon
6. Wait untill the sun's up :)


Maybe a "stupid" question, but can you use the standard (Eneco) optic sensor with this module ?
User avatar
madpatrick
Member
Member
 
Posts: 63
Joined: December 2017
Location: Zuid-Holland

Re: ZonOpToon alternative

Postby TerrorSource » Fri Nov 23, 2018 5:09 pm

Well you need to. There is no other option to read the data from the Solar module with the Meteradapter.
TerrorSource
Member
Member
 
Posts: 179
Joined: May 2017

Re: ZonOpToon alternative

Postby TheHogNL » Fri Nov 23, 2018 5:49 pm

TerrorSource wrote:Well you need to. There is no other option to read the data from the Solar module with the Meteradapter.


Led optic (via the sensor) or wired using S0 is both possible. Eneco doesn't connect using S0, only using the optic sensor though.
Member of the Toon Software Collective
User avatar
TheHogNL
Advanced Member
Advanced Member
 
Posts: 544
Joined: August 2017

Re: ZonOpToon alternative

Postby madpatrick » Sun Dec 09, 2018 11:18 am

Where can you get the mountingclip to mount the sensor to the KwH meter ?
Is this supplied with the Toon ? it was not with the KwH module
User avatar
madpatrick
Member
Member
 
Posts: 63
Joined: December 2017
Location: Zuid-Holland

Re: ZonOpToon alternative

Postby TheHogNL » Sun Dec 09, 2018 7:55 pm

madpatrick wrote:Where can you get the mountingclip to mount the sensor to the KwH meter ?
Is this supplied with the Toon ? it was not with the KwH module


It is supplied with the sensors. Nowadays the sensors are not included standard in a new toon.

But I would advice to make a s0 wired connection instead of reading the led with the sensor. This is much more precise.
Member of the Toon Software Collective
User avatar
TheHogNL
Advanced Member
Advanced Member
 
Posts: 544
Joined: August 2017

Re: ZonOpToon alternative

Postby madpatrick » Sun Dec 09, 2018 11:12 pm

It is working bit indeed not accurate.
Even at night is say it is producing 6w
User avatar
madpatrick
Member
Member
 
Posts: 63
Joined: December 2017
Location: Zuid-Holland

Re: ZonOpToon alternative

Postby TheHogNL » Mon Dec 10, 2018 8:01 am

madpatrick wrote:It is working bit indeed not accurate.
Even at night is say it is producing 6w


This is your inverter in night mode taking some power. Which kWh meter are you using? Some calculate in both directions indepently, some caclulate both directions together.
Member of the Toon Software Collective
User avatar
TheHogNL
Advanced Member
Advanced Member
 
Posts: 544
Joined: August 2017

Re: ZonOpToon alternative

Postby madpatrick » Mon Dec 10, 2018 8:40 am

TheHogNL wrote:This is your inverter in night mode taking some power. Which kWh meter are you using? Some calculate in both directions indepently, some caclulate both directions together.


I'm using the INEPRO KWH1073PRO.
Not sure if this is calculating both directions.
Will this be resolvd by wiring S0 instead of optic sensor?
User avatar
madpatrick
Member
Member
 
Posts: 63
Joined: December 2017
Location: Zuid-Holland

Re: ZonOpToon alternative

Postby TheHogNL » Mon Dec 10, 2018 4:54 pm

Eneco also is using this meter (pro1-s, not the pro1-2t but almost the same).
S0 or led doesn't make a difference in what is is doing.

However, look at the manual https://ineprometering.com/wp-content/u ... -V2.18.pdf section 7.11. I'm not sure but it looks like you can config if you want forward, reverse, both, the difference etc only.
Member of the Toon Software Collective
User avatar
TheHogNL
Advanced Member
Advanced Member
 
Posts: 544
Joined: August 2017

Re: ZonOpToon alternative

Postby madpatrick » Mon Dec 10, 2018 9:22 pm

TheHogNL wrote:Eneco also is using this meter (pro1-s, not the pro1-2t but almost the same).
S0 or led doesn't make a difference in what is is doing.

However, look at the manual https://ineprometering.com/wp-content/u ... -V2.18.pdf section 7.11. I'm not sure but it looks like you can config if you want forward, reverse, both, the difference etc only.

I will try to change the setup
Only now find the button....
User avatar
madpatrick
Member
Member
 
Posts: 63
Joined: December 2017
Location: Zuid-Holland

Re: ZonOpToon alternative

Postby TheHogNL » Mon Dec 10, 2018 9:33 pm

Isn't it the big arrow? Just like in this video (different brand, 3 fase.. but you see what i mean :) https://www.youtube.com/watch?v=zazgV3QtJaA )
Member of the Toon Software Collective
User avatar
TheHogNL
Advanced Member
Advanced Member
 
Posts: 544
Joined: August 2017

Previous

Return to Toon Hardware

Who is online

Users browsing this forum: No registered users and 1 guest