Toon App: Water

[Tebogo]

Wemos will be restarted and connect with a fixed IP.

Goto the ip adress in a browser and you will see the toonWater main page.

The last step does not work. After getting a fixed IP-address which I get confirmed in DHCP, it disconnects and stays offline.
The blue led is continues on.

I also cannot ping the Wemos.

It should be possible to browse to the wemos toonWater main page without connected the sensor?

[Jasper]

You in the same range?

So not 10.15 but 1.15

It's IP,
Host IP
Subdomain I think it's called 255.255.255.0

[Tebogo]

You in the same range?

So not 10.15 but 1.15

It's IP,
Host IP
Subdomain I think it's called 255.255.255.0

All my ESP's get IP-address from DHCP, in where I define which IP-address.
Subnet and DNS and Gateway are all defined in DHCP.

So that should work.

I 'll flash again, and try manual.

EDIT:
Oke, so DHCP does not work. You have to set manually the ip-address. That's where I went wrong.
Onwards with testing!

Thank you!

[Jasper]

During setup it need to be set manually even when you have dhcp on

[oepi-loepi]

During setup it need to be set manually even when you have dhcp on

Yes i switched off. the DHCP option. You must set an IP adress manually! This because toon has to connect to this adress and DHCP can change when rebooting the device.

[Tebogo]

During setup it need to be set manually even when you have dhcp on

Yes i switched off. the DHCP option. You must set an IP adress manually! This because toon has to connect to this adress and DHCP can change when rebooting the device.

I use DHCP reservations to solve that issue

[oepi-loepi]

During setup it need to be set manually even when you have dhcp on

Yes i switched off. the DHCP option. You must set an IP adress manually! This because toon has to connect to this adress and DHCP can change when rebooting the device.

I use DHCP reservations to solve that issue

Yes, i did the same but most people love the DHCP and then forget about it or do not know the router reservations so to solve that so i removed the DHCP option.

[gert848]

Hello Oepi Loepi, Very nice App.

I had not enough room at the top off the meter.
I built it with the original Analog sensor delivered by the Toon1
This sensor was used for analog measure for gas and electic meter.
I test it now and later i will make picture and sent it to this post.

This app is a very good idea that we have now power usage gas and water in one component.

[oepi-loepi]

Hello Oepi Loepi, Very nice App.

I had not enough room at the top off the meter.
I built it with the original Analog sensor delivered by the Toon1
This sensor was used for analog measure for gas and electic meter.
I test it now and later i will make picture and sent it to this post.

This app is a very good idea that we have now power usage gas and water in one component.

Whow! Brilliant to use the sensor which came with toon. I look forward to the pictures and a little sketch how to connect.

[Daniel]

I just try to flash the wemos D1.
When I open FlashESP8266.exe the com is oke, but the firmware is blank?! Can’t choose anything.

Maybe I forget something?

[oepi-loepi]

I just try to flash the wemos D1.
When I open FlashESP8266.exe the com is oke, but the firmware is blank?! Can’t choose anything.

Maybe I forget something?

You have to put the .bin in the correct folder (same as the exe. Or a folder. .bin) Then restart FlashESP8266.exe and the firmware should be in dropdown menu.

[Daniel]

I just try to flash the wemos D1.
When I open FlashESP8266.exe the com is oke, but the firmware is blank?! Can’t choose anything.

Maybe I forget something?

You have to put the .bin in the correct folder (same as the exe. Or a folder. .bin) Then restart FlashESP8266.exe and the firmware shoud be in dropdown menu.

thanks, now its working!

[EchoNL]

Nice project. Ordered the stuff and will get it soon!

Question if you can make this waterapp, is it possible to make a humidity and temperature app for the Toon?
For this you can also use a Wemos D1 Mini a 10k resistor and a DHT22 (temp and humidity sensor). A lot of video's on youtube about those projects.

Keep up the good work!

[Toonz]

Is possible of course. Note that a Toon 2 already has a built-in humidity sensor and tile.

[oepi-loepi]

Is possible of course. Note that a Toon 2 already has a built-in humidity sensor and tile.

Is this the same as the TemperatureLogger app from the toonstore? viewtopic.php?f=99&t=11684

Since toon doesn't have databases for the temperature and humidity it is not possible to get these readings in the standard graphs like power, gas, solar and water.