Toon 1 and Toon 2 software rooting
Moderators: marcelr, TheHogNL, Toonz, TerrorSource
Re: Toon 1 and Toon 2 software rooting
Hard to tell what is going wrong as you are using networkmanager. Maybe that conflicts with the temporary added IP addresses in the script where the payload is loaded from.
Just try again to make the network working without networkmanager or go ahead and use the boot laptop method which is based on the same script b
Just try again to make the network working without networkmanager or go ahead and use the boot laptop method which is based on the same script b
Member of the Toon Software Collective
Re: Toon 1 and Toon 2 software rooting
So I did the install of Kali based on https://github.com/JackV2020/Root-A-Toon-USB-Stick.
Despite I get the same result: "Response payload was net sent. Please try again.
I use a normal laptop and I boot from USB directly to Kali (32B version).
Install of Wifi Network is succesfull and Toon2 can connect.
The running the script (also test) but no other response than payload was not sent.
From the Wifiscript the SSID is ToonRouter.
Toon2 receives IP-address 10.42.0.188.
After reboot no connection with servicecenter
After multiple attemps to root, Toon2 automatically gets connection with ServiceCenter without having done a reboot.
by the way, Kali and the script also uses netwerk manager....
This is getting a bit annoying.....
Despite I get the same result: "Response payload was net sent. Please try again.
I use a normal laptop and I boot from USB directly to Kali (32B version).
Install of Wifi Network is succesfull and Toon2 can connect.
The running the script (also test) but no other response than payload was not sent.
From the Wifiscript the SSID is ToonRouter.
Toon2 receives IP-address 10.42.0.188.
After reboot no connection with servicecenter
After multiple attemps to root, Toon2 automatically gets connection with ServiceCenter without having done a reboot.
by the way, Kali and the script also uses netwerk manager....
This is getting a bit annoying.....
Toon2 with 5.49.16 firmware TSC 2.1.6
Apps: Sonos, Calender, garbagecalender, traffic information, webcam, doorcam, PostNL, Onkyo, Domoticzboard and weather app.
Apps: Sonos, Calender, garbagecalender, traffic information, webcam, doorcam, PostNL, Onkyo, Domoticzboard and weather app.
Re: Toon 1 and Toon 2 software rooting
ok, 2 things I'm wondering
1. is there an option to set the time-out to a longer period, to wait for the payload?
2. When I do the full reset on Toon2 and it goes back to factory default with software 4.someting. What impact does it have? will I be able to update/upgrade/activate again?
1. is there an option to set the time-out to a longer period, to wait for the payload?
2. When I do the full reset on Toon2 and it goes back to factory default with software 4.someting. What impact does it have? will I be able to update/upgrade/activate again?
Toon2 with 5.49.16 firmware TSC 2.1.6
Apps: Sonos, Calender, garbagecalender, traffic information, webcam, doorcam, PostNL, Onkyo, Domoticzboard and weather app.
Apps: Sonos, Calender, garbagecalender, traffic information, webcam, doorcam, PostNL, Onkyo, Domoticzboard and weather app.
Re: Toon 1 and Toon 2 software rooting
Maybe your firmware is indeed not working anymore with the rooting. Need to check that.
You can try the recovery (= not factoryreset). As it already has the new VPN keys it is not a problem to go to the recovery reset and then try to root.
You can try the recovery (= not factoryreset). As it already has the new VPN keys it is not a problem to go to the recovery reset and then try to root.
Member of the Toon Software Collective
Re: Toon 1 and Toon 2 software rooting
Ok, I did the recovery and I have now 4.9.124 software version.
But when pressing software nothing happens (doesn't check for new software.
What should I do first now?
Toon2 is connected with Wifi ToonRouter network and says its connected with internet.
I do get an old error "D03" which says it can't connect to the service center.....
But when pressing software nothing happens (doesn't check for new software.
What should I do first now?
Toon2 is connected with Wifi ToonRouter network and says its connected with internet.
I do get an old error "D03" which says it can't connect to the service center.....
Toon2 with 5.49.16 firmware TSC 2.1.6
Apps: Sonos, Calender, garbagecalender, traffic information, webcam, doorcam, PostNL, Onkyo, Domoticzboard and weather app.
Apps: Sonos, Calender, garbagecalender, traffic information, webcam, doorcam, PostNL, Onkyo, Domoticzboard and weather app.
Re: Toon 1 and Toon 2 software rooting
On 4.9.124 I remember it can take some while for it to get the software check done but just keep trying
Member of the Toon Software Collective
Re: Toon 1 and Toon 2 software rooting
ok, so waited until now but no connection.
Wondering:
Should I connect with the script or should Toon2 first connect to normal network then update/upgrade and retry the script?
Wondering:
Should I connect with the script or should Toon2 first connect to normal network then update/upgrade and retry the script?
Toon2 with 5.49.16 firmware TSC 2.1.6
Apps: Sonos, Calender, garbagecalender, traffic information, webcam, doorcam, PostNL, Onkyo, Domoticzboard and weather app.
Apps: Sonos, Calender, garbagecalender, traffic information, webcam, doorcam, PostNL, Onkyo, Domoticzboard and weather app.
Re: Toon 1 and Toon 2 software rooting
You could try that indeed.
The toon must have had one succesfull VPN connection before I do remember (haven't rooted for long time)
The toon must have had one succesfull VPN connection before I do remember (haven't rooted for long time)
Member of the Toon Software Collective
Re: Toon 1 and Toon 2 software rooting
Finally succeeded!
Based on my experiences a short instruction.
So to all who have a Toon2 with software version 6.02 unrooted and want to root:
1. Setup a RaspBerry Pi as Wifi Access Point with router functionality and make sure you have an SSID.
Instructions can be found on https://www.raspberrypi.com/documentati ... cess-point as part of https://github.com/ToonSoftwareCollective/Root-A-Toon
Make sure you can connect to the SSID and have stable internet connection!
In case this doesn't work try https://github.com/JackV2020/Root-A-Toon-USB-Stick and follow the instructions.
This one worked the best for me, installed Kali on USB stick and booted from laptop.
(make sure you setup the wifi SSID part)
2. First execute recovery of Toon2 (recovery is something else the factory reset!!)
3. After recovery is successfull, connect Toon2 to a normal network and make sure it has connected once but DO NOT upgrade!
4. Reboot
5. Connect to the SSID you have created on your RaspberryPi (or with Kali)
6. Reboot
7. Now its time to first Activate your Toon2, follow the steps as described on https://github.com/ToonSoftwareCollective/Root-A-Toon and mentioned in the script, but still DO NOT upgrade!
8. Reboot
9. After the activation completed successfully you can start trying to TEST root based on https://github.com/ToonSoftwareCollective/Root-A-Toon or when based on https://github.com/JackV2020/Root-A-Toon-USB-Stick but still DO NOT upgrade
10. Reboot
11. If Test root is successfull you can start trying to root your Toon2on https://github.com/ToonSoftwareCollective/Root-A-Toon or when based on https://github.com/JackV2020/Root-A-Toon-USB-Stick but still DO NOT upgrade
12. Reboot
13. You can Upgrade now (via Software)
In case the update doesn't start automated, login via SSH (using Putty or somehting like that) and perform manualy the update.
Instructions can be found at https://github.com/ToonSoftwareCollective/update-rooted
Good luck!
Based on my experiences a short instruction.
So to all who have a Toon2 with software version 6.02 unrooted and want to root:
1. Setup a RaspBerry Pi as Wifi Access Point with router functionality and make sure you have an SSID.
Instructions can be found on https://www.raspberrypi.com/documentati ... cess-point as part of https://github.com/ToonSoftwareCollective/Root-A-Toon
Make sure you can connect to the SSID and have stable internet connection!
In case this doesn't work try https://github.com/JackV2020/Root-A-Toon-USB-Stick and follow the instructions.
This one worked the best for me, installed Kali on USB stick and booted from laptop.
(make sure you setup the wifi SSID part)
2. First execute recovery of Toon2 (recovery is something else the factory reset!!)
3. After recovery is successfull, connect Toon2 to a normal network and make sure it has connected once but DO NOT upgrade!
4. Reboot
5. Connect to the SSID you have created on your RaspberryPi (or with Kali)
6. Reboot
7. Now its time to first Activate your Toon2
Code: Select all
sudo bash activate-toon.sh
8. Reboot
9. After the activation completed successfully you can start trying to TEST root based on https://github.com/ToonSoftwareCollective/Root-A-Toon
Code: Select all
sudo bash root-toon.sh
Code: Select all
sudo bash root-toon.sh test
10. Reboot
11. If Test root is successfull you can start trying to root your Toon2on https://github.com/ToonSoftwareCollective/Root-A-Toon
Code: Select all
sudo bash root-toon.sh payload
Code: Select all
sudo bash root-toon.sh root
12. Reboot
13. You can Upgrade now (via Software)
In case the update doesn't start automated, login via SSH (using Putty or somehting like that) and perform manualy the update.
Instructions can be found at https://github.com/ToonSoftwareCollective/update-rooted
Good luck!
Toon2 with 5.49.16 firmware TSC 2.1.6
Apps: Sonos, Calender, garbagecalender, traffic information, webcam, doorcam, PostNL, Onkyo, Domoticzboard and weather app.
Apps: Sonos, Calender, garbagecalender, traffic information, webcam, doorcam, PostNL, Onkyo, Domoticzboard and weather app.