CTX35 Stoped working, is oke now!!

Post by **Paul H te O** » Tue Dec 16, 2008 11:17 pm

Hell0, that is not so fine but can I use the EZL-200F with other VCP software, and if yes whitch VCP software?

<blockquote id="quote">quote:<hr height="1" noshade id="quote">Originally posted by Bwired
 Right Robert, He needs to use the virtual comport and can't address directly to IP

Post by **Digit** » Tue Dec 16, 2008 11:26 pm

I only know of device-specific software that can do this. So it has to come with he hardware or else no luck. You can always send it back within 7 days without a problem i think.

Post by **drmacchi** » Wed Dec 17, 2008 12:27 am

Robert , why there is not software? From antratek website :" Network converters
With the ezTCP converters of Sollae Systems you can easily connect serial devices to wired (Ethernet) or wireless (WLAN) networks. Software is available for installation and TCP settings: ezVSP, ezConfig, ezTerm, etc. By use of the Virtual COM Port Driver data communication is the same as a direct connection to the COM port of the PC."

Post by **Digit** » Wed Dec 17, 2008 12:41 am

Hmm, from what i can remember there only were things like firmware, manual and a setup-tool (IP-address, port, operating mode etc.) on the CD. But i could be wrong! We'll know soon

Post by **Paul H te O** » Wed Dec 17, 2008 10:44 am

I found the software, I'm gone place it as soon as the module is arrived and wil let you all know about the result.

<blockquote id="quote">quote:<hr height="1" noshade id="quote">Originally posted by Digit
 Hmm, from what i can remember there only were things like firmware, manual and a setup-tool (IP-address, port, operating mode etc.) on the CD. But i could be wrong! We'll know soon

Post by **Paul H te O** » Thu Jan 15, 2009 6:24 pm

The EZL-200F is working!!! It works well and is running stable now for a few days.
(It took a while because there was no power supply whit it and I had no serial cable.)
Thanks for the help Regards Paul.
<blockquote id="quote">quote:<hr height="1" noshade id="quote">Originally posted by Paul H te O
 I found the software, I'm gone place it as soon as the module is arrived and wil let you all know about the result.

<blockquote id="quote">quote:<hr height="1" noshade id="quote">Originally posted by Digit
 Hmm, from what i can remember there only were things like firmware, manual and a setup-tool (IP-address, port, operating mode etc.) on the CD. But i could be wrong! We'll know soon

Post by **Willem4ever** » Wed Jul 22, 2009 5:47 pm

ezVSP seems to run as a normal application, not as a service. How did you manage to make it work with Homeseer. (In my case HS runs as a service)

Post by **Paul H te O** » Wed Jul 22, 2009 6:47 pm

<blockquote id="quote">quote:<hr height="1" noshade id="quote">Originally posted by willem4ever
 ezVSP seems to run as a normal application, not as a service. How did you manage to make it work with Homeseer. (In my case HS runs as a service)
<hr height="1" noshade id="quote"></blockquote id="quote">
Hi Willem, I just put the com port on the ezVSP application the same as the com port of the act-ti203 plug-in in Homeseer.
And it worked.

Post by **Willem4ever** » Wed Jul 22, 2009 7:48 pm

But ezVSP only starts when log-on as an user, my HS computer runs without users logging-on.

Post by **Alexander** » Wed Jul 22, 2009 8:42 pm

@willem: try this: http://www.iopus.com/guides/srvany.htm