RFXtrx433 and NEXA PB-3
Moderator: b_weijenberg
RFXtrx433 and NEXA PB-3
Hi,
I have an RFXtrx433 which I try to use with the NEXA PB-3. It seems like the RFXtrx433 do not recognize what the transmitter sends. Since the NEXA PB-3 can store three codes, I do can use the NEXA remote and the RFXtrx433 switching it of and off, that’s fine, but if the RFXtrx433 would recognize what code (on or off) the remote sends, I could do other things as well. Shouldn’t that be the case?
///Knasen (the rookie)
I have an RFXtrx433 which I try to use with the NEXA PB-3. It seems like the RFXtrx433 do not recognize what the transmitter sends. Since the NEXA PB-3 can store three codes, I do can use the NEXA remote and the RFXtrx433 switching it of and off, that’s fine, but if the RFXtrx433 would recognize what code (on or off) the remote sends, I could do other things as well. Shouldn’t that be the case?
///Knasen (the rookie)
- b_weijenberg
- Forum Moderator
- Posts: 1744
- Joined: Sun May 14, 2006 4:32 pm
- Location: Netherlands
Re: RFXtrx433 and NEXA PB-3
Which device type do you use to control the NEXA PB-3?
is the remote compatible with the AC code?
is the remote compatible with the AC code?
Re: RFXtrx433 and NEXA PB-3
Hi
It is the one that was included in the packackage and on its backside it says "PBT-707". Thanks!
It is the one that was included in the packackage and on its backside it says "PBT-707". Thanks!
- b_weijenberg
- Forum Moderator
- Posts: 1744
- Joined: Sun May 14, 2006 4:32 pm
- Location: Netherlands
Re: RFXtrx433 and NEXA PB-3
which protocol is used in RFXmngr to control this unit?
Re: RFXtrx433 and NEXA PB-3
Sorry for late reply. AC works. (ANSLUT, works too, but not HE EU)
- b_weijenberg
- Forum Moderator
- Posts: 1744
- Joined: Sun May 14, 2006 4:32 pm
- Location: Netherlands
Re: RFXtrx433 and NEXA PB-3
Use the latest firmware,
enable only the HE EU protocol and check if HE EU is received.
Some protocols cannot be received when another is enabled.
enable only the HE EU protocol and check if HE EU is received.
Some protocols cannot be received when another is enabled.
Re: RFXtrx433 and NEXA PB-3
I flashed it with with FW 42. Disabled everything except HE EU. RFXmngr 7.0.0.8 does not understand the codes sent from remote controller PBT-707 (included in the package PB-3).
Setting the receiver in programming mode, I can program it to receive AC or ANSLUT, but not HE EU.
Setting the receiver in programming mode, I can program it to receive AC or ANSLUT, but not HE EU.
- b_weijenberg
- Forum Moderator
- Posts: 1744
- Joined: Sun May 14, 2006 4:32 pm
- Location: Netherlands
Re: RFXtrx433 and NEXA PB-3
it is normal. An AC remote cannot be received in HE EU mode.
Re: RFXtrx433 and NEXA PB-3
So PBT-707 does not work... Which NEXA remote do work?
- b_weijenberg
- Forum Moderator
- Posts: 1744
- Joined: Sun May 14, 2006 4:32 pm
- Location: Netherlands
Re: RFXtrx433 and NEXA PB-3
I suppose the PB-3 remote does not transmit AC codes.
This remote should be received but needs the RFXtrx433 hardware version 1.0 http://www.nexa.se/LYCT-705-Vit.htm
If you have a version 0.0 you can request RFXCOM for the procedure to exchange the RFXtrx.
BTW: Sartano remotes are not supported for receive! See the RFXtrx User Guide chapter 2.1 which devices are supported for receive and transmit.
This remote should be received but needs the RFXtrx433 hardware version 1.0 http://www.nexa.se/LYCT-705-Vit.htm
If you have a version 0.0 you can request RFXCOM for the procedure to exchange the RFXtrx.
BTW: Sartano remotes are not supported for receive! See the RFXtrx User Guide chapter 2.1 which devices are supported for receive and transmit.
Re: RFXtrx433 and NEXA PB-3
The FW 45 supports PBT-707! Thanks!
Re: RFXtrx433 and NEXA PB-3
...and with FW 50 we are back on track. Thanks!