Page 3 of 3
Re: Jeenode + roomboard: switching output from Homeseer
Posted: Sun Jan 02, 2011 7:53 pm
by Digit
Yes, but...
It would mean a complete 'makeover' of both the sketch and the Homeseer scripts.
Re: Jeenode + roomboard: switching output from Homeseer
Posted: Mon Jan 03, 2011 1:46 pm
by nawikre
Oke...so it actually means writing new script and sketch. And i am no programmer so that is impossible for me to do....
IF someone wants to put in the effort to do this, I (and many others) are very greatfull....
but i think i should open a new topic for this issue??
Iwan
Re: Jeenode + roomboard: switching output from Homeseer
Posted: Mon Jan 03, 2011 4:14 pm
by Digit
Using Arduino's or comparable cannot be done without at least a bit of programming experience, so I don't get it...
You can open a new topic, but don't expect too much - speaking for myself, I'm not gonna invest time in "Arduino via USB" Homeseer Integration when JeeNode & Homeseer integration already exists.
And in my opinion, a JeeNode with RF is much more suitable as sensor node as the "original" Arduino. If I were you, I would get hold of 2 JeeNodes, put the Arduino on Marktplaats (or keep it for misc. testing purposes would be a better choice) and you (and those many others) are almost done... am I right or not?
If not, please say so
![Smile :)](./images/smilies/icon_smile.gif)
Re: Jeenode + roomboard: switching output from Homeseer
Posted: Mon Jan 03, 2011 9:58 pm
by nawikre
Digit wrote:Using Arduino's or comparable cannot be done without at least a bit of programming experience, so I don't get it...
You can open a new topic, but don't expect too much - speaking for myself, I'm not gonna invest time in "Arduino via USB" Homeseer Integration when JeeNode & Homeseer integration already exists.
And in my opinion, a JeeNode with RF is much more suitable as sensor node as the "original" Arduino. If I were you, I would get hold of 2 JeeNodes, put the Arduino on Marktplaats (or keep it for misc. testing purposes would be a better choice) and you (and those many others) are almost done... am I right or not?
If not, please say so
![Smile :)](./images/smilies/icon_smile.gif)
oke, that is a real option, but the next question will be....What IF i only need a jeenode with temp sensor and not a whole roomboard with motion detection and light.
Iwan
Re: Jeenode + roomboard: switching output from Homeseer
Posted: Tue Jan 04, 2011 1:15 am
by Rene
Buy the thermo plug (board only) and a DS18B20, more details
here
Re: Jeenode + roomboard: switching output from Homeseer
Posted: Tue Jan 04, 2011 9:57 am
by nawikre
Rene wrote:Buy the thermo plug (board only) and a DS18B20, more details
here
oke, but what about humid sensor, because it would be perfect to have temp and humid
thanks, this option is a very good one.
Iwan
Re: Jeenode + roomboard: switching output from Homeseer
Posted: Tue Jan 04, 2011 10:07 am
by Digit
SHT11, S555TH can do that.
For SHT11 you could use the Room Board.
Another resource:
http://www.jansipke.nl/measuring-temper ... -a-jeenode
Including sketch
I found that one with the help of an Internet search engine
![Wink :wink:](./images/smilies/icon_wink.gif)
Re: Jeenode + roomboard: switching output from Homeseer
Posted: Tue Jan 04, 2011 11:52 am
by nawikre
thank you very much......i use an old search engine, so it did'nt popup
i have looked at the link, but the are connecting a extra/different radio. type RX868 for recieving the data from a external (big) temp/humid sensor.
what i actually wanted was like the jeenode roomboard without pir and light. (without having to buy the roomboard and pull the other 2 modules of the board.
Iwan
Re: Jeenode + roomboard: switching output from Homeseer
Posted: Tue Jan 04, 2011 4:48 pm
by nawikre
i finally get the picture.......
you have the jeenode...and as extra you have the roomboard that you plug intoo the jeenode to make 1 set. So you have to buy these 2 things seperatly.
so i can take a jeenode and a seperate temp and humid sensor to plug it into the jeenode.....
am i right??
Iwan
Re: Jeenode + roomboard: switching output from Homeseer
Posted: Tue Jan 04, 2011 7:54 pm
by esschenk
Hello,
Yes right thats all you need
http://jeelabs.com/products/jeelink
http://jeelabs.com/products/jeenode
http://jeelabs.com/products/room-board
Maybe you can ask Jean if you can buy only the roomboard with the Sht11
else you can buy only the roomboard pcb and buy the sht11 somewhere else
http://cgi.ebay.com/SHT11-Humidity-Temp ... _500wt_922
Good luck
Ed
Re: Jeenode + roomboard: switching output from Homeseer
Posted: Tue Jan 04, 2011 8:07 pm
by nawikre
this is the answert i was looking/hoping for....
thanks, Ed