Rooting Toon (or boxx)

Forum about the tweaking of the Eneco Toon.

Moderator: marcelr

Re: Rooting Toon (or boxx)

Postby jumperone » Thu May 03, 2018 5:32 pm

activate Toon


I have seen what I did wrong
The location was good.
/mnt/data/qmf/config/config_happ_scsync.xml
<visibility>0</visibility><StartDate>0</StartDate><EndDate>0</EndDate
I should have stood before the rule and walked in with the cursor .
Then press I (insert) to adjust it.and the previous delete
I also solved my previous post (no gas display).
<GasDisplay>0</GasDisplay> <GasDisplay>1</GasDisplay>
On that line I also adjusted that from 0 after 1.

For further adjustment see
TerrorSource
https://www.domoticaforum.eu/viewtopic. ... 971#p83254
I have the toon with Version: 2.0 - ThehogNL - 24-3-2018 upgrade from version 2.9.26 upgrade to 4.10.6. Update failled / Bus error

OPKG Do Not Work / Bus error / orange screen with 2 points.
What can I do
jumperone
Starting Member
Starting Member
 
Posts: 8
Joined: April 2018

Re: Rooting Toon (or boxx)

Postby Markie13 » Thu May 10, 2018 1:33 pm

@Markie13:

Sounds like a serial IO issue. Are you sure RxD and TxD are in the right place? Is your serial converter working properly with other hardware?


From the "Fully automated rooting script" topic to here.

It finally succeeded. I added password toon right after reboor. I didn't wait till "enter password". After ten times rebooting i succeeded :D

Now i get stuck at this
Restoring the boot loader and accessing toon through a shell


The only eneco i see is this
Lease failing, starting in bg: udhcpc -b -R -i eth0 -A 5 -p /var/run/udhcpc.eth0.pid -H eneco-001-******
Replaced serial number with asteriks

My reset button seems not to work so at the and of
Locate the password file /etc/passwd and edit the line:

root:DISABLED:0:0:root:/root:/bin/sh

to read:

root::0:0:root:/root:/bin/sh
so i can not reset.
Markie13
Starting Member
Starting Member
 
Posts: 11
Joined: May 2018

Re: Rooting Toon (or boxx)

Postby Markie13 » Mon May 14, 2018 8:03 pm

I have fully rooted my toon. For installing dropbear and openssh i used unpacked .ipk files from http://files.domoticaforum.eu/index.php?cam=/Toon. Maybe an idea to adjust/add this to your guide Marcel. Makes rooting much easier.
Markie13
Starting Member
Starting Member
 
Posts: 11
Joined: May 2018

Re: Rooting Toon (or boxx)

Postby TheHogNL » Tue May 15, 2018 6:53 am

Markie13 wrote:I have fully rooted my toon. For installing dropbear and openssh i used unpacked .ipk files from http://files.domoticaforum.eu/index.php?cam=/Toon. Maybe an idea to adjust/add this to your guide Marcel. Makes rooting much easier.


Why? You don't need 'unpacked' ipk. Just install it with opkg as the manual states.
TheHogNL
Member
Member
 
Posts: 261
Joined: August 2017

Re: Rooting Toon (or boxx)

Postby Markie13 » Tue May 15, 2018 8:47 am

TheHogNL wrote:
Markie13 wrote:I have fully rooted my toon. For installing dropbear and openssh i used unpacked .ipk files from http://files.domoticaforum.eu/index.php?cam=/Toon. Maybe an idea to adjust/add this to your guide Marcel. Makes rooting much easier.


Why? You don't need 'unpacked' ipk. Just install it with opkg as the manual states.

Normally it will work, but wget on my toon had some problems with wget and https. So I was searching for solutions. So this was mine.
Markie13
Starting Member
Starting Member
 
Posts: 11
Joined: May 2018

Re: Rooting Toon (or boxx)

Postby TheHogNL » Tue May 15, 2018 9:32 am

Markie13 wrote:Normally it will work, but wget on my toon had some problems with wget and https. So I was searching for solutions. So this was mine.


The domotica forum files url is in HTTP and not HTTPS.

But nice to see you managed to worked around your issue yourself.
TheHogNL
Member
Member
 
Posts: 261
Joined: August 2017

Previous

Return to Eneco Toon as Domotica controller

Who is online

Users browsing this forum: No registered users and 1 guest