Home Automation Domotica Forum Europe, Bwired Forum

I've been using a Fit-PC2 for about a year now, 7W max power consumption or something ridiculously low like that, running win7. No moving parts, I placed a SSD disk in it, and I also ordered the heatsink. It's been hanging in my garage, which can get a little warm in the summer, no problems at all. ...

Stupid me: it beeps when it's not placed in the dock, just to alarm you that it's on battery power. Can't find that anywhere in the manual. Did a reset to factory settings yesterday, everything seemed to work fine, when I raised the asking temperature a couple degrees the heating switched on, when I...

Well, still ordered the radiator pack, using it without HS will still be an improvement on my current thermostat system. Had some problems getting it to work with my modulating central heating unit. The Evotouch was able to turn on the heating, but after that it didn't stop heating anymore, temperat...

It has been quiet for ten moths, still no luck with the protocol? I'm going to order the Evotouch radiator set, everytime the fire is burning in our fireplace the rest of the house freezes up. Would be nice if we could also find a way to control it through homeseer or another interface.

Correct, same here again, I didn't receive any answer on my inquiries by mail too two weeks ago. Was planning to order a couple of switches, ended up ordering at Tane's shop, since he did reply the same day. Too bad.

Looks the same here:
Everspring 101 H 1 H False 2.9 (ZDK Version 4,22) App: 1.0 Acceptable (5) 40.0Kbps Basic: ROUTING SLAVE
Generic: SENSOR BINARY
SENSOR BINARY, CONFIGURATION V2, WAKE UP, MANUFACTURER SPECIFIC, VERSION, ASSOCIATION V2, BATTERY


I'll have to test later today...

Morten, I'm not sure if this is the same function, this is how long the switch will stay ON, it has no influence on how long it will take before it starts detecting and switching again. The HSM100 is available for switching within a minute, the Everspring/Eminent only after more then 10 minutes (sti...

Just found out it should be an Everspring SP103, I did find some parameter information here: http://www.pepper1.net/zwavedb/device/59 Great Z-wave device database by the way! No luck there though, the mentioned parameters won't help me with my problem. I like this motion detector, but I want it to r...

Just tested an Eminent EM6580 motion detector. Feels like a very solid device, build quality is good. Took me a while to get it working, it's necessary to associate it with Homeseer, and you have to wait for a timeout before you can retrigger. So at first it looks like it works only one time, and fa...

Received my last order (couple of z-wave devices) that same week, looks like Ezhome is back in business.

Same here, I also had to wait for months before even getting an answer on a Duwi RMA and did not receive any answers to other email messages (mainly questions about which product to buy). I had lost all faith in Ezhome and was looking for other suppliers. Until about 1 or 2 weeks ago, suddenly got a...

Ok, I downloaded the Danfoss utility, but how should I configure these settings? I figure I need to go to advanced, and the tab "configuration", but which parameter do I have to set to 00 to remove the 2 minute on function and set it to permanent? The german manual which came with the Duwi...

R_255, heb je al iets kunnen maken in HS waarbij je de status kunt uitlezen? Ik wil ook iets dergelijks maken, maar dan voor aansturen van Somfy rolluiken en zonneschermen. Ik moet ook via de compoort commando's versturen, en kan de status uitlezen door een commando te sturen waarna je een post ontv...

Ik zag net dat het idd Visonic is. In de manual van de MCT-302 staat 433 en 868 Mhz, maar ik zie nergens of deze beide frequenties onboard heeft (lijkt me sterk), of dat er per frequentie een ander model is. Ik heb nl alleen 433MHz zend/ontvang in mijn RFXcom. Ik ga gewoon de KAKU eens proberen, de ...

Kaku bel vertrouw ik niet meer. Zeker 10% wordt er gemist in mijn opstelling. En twee keer uit bed gebeld midden in de nacht.. Ik wacht op de ombouw van mijn Conrad bel. Deze ga ik dan via mct302 of een zwave module aan homeseer conecten. Enver, help me out: die MCT-302 kwam ik tegen bij Becu, er s...