klikaan klikuit AMST-606

Post by **Harry** » Tue Jun 24, 2008 2:07 am

I have an AMST-606 magnet contact from KAKU.
This moduul uses automatic coding.
how can i add this divice
can i do this whit the plugin for homeseer.
on the "RFmonitor" i recieve somthing.
how can i do this

Post by **b_weijenberg** » Tue Jun 24, 2008 8:19 am

Add the KAKU door sensor in the RFXCOM plug-in on the Input Sensors configuration tab.

Post by **KolNedra** » Mon Aug 11, 2008 11:03 am

I have got a CM15 (http://www.elekhomica.nl/product_info.p ... cts_id=761), is it possible to receive the AMST-606 signals on this interface, without a RFXCOM?

Post by **b_weijenberg** » Mon Aug 11, 2008 12:41 pm

The CM15 can only receive X10.

Post by **KolNedra** » Mon Aug 11, 2008 1:06 pm

So if I want to receive KAKU RF signals from that AMST-606 I have to purchase a RFX receiver (http://www.rfxcom.com/receivers.htm) ?

Post by **b_weijenberg** » Mon Aug 11, 2008 1:19 pm

yes, the RFXCOM 433.92MHz receiver is able to receive the KAKU signals.

Post by **KolNedra** » Mon Aug 11, 2008 1:22 pm

Then I'm going to purchase an RFXCOM receiver, since the KAKU sensors are cheaper and look nicer.
Thanks for you quick replies, I'm quite new with home automation, but very eager to learn!

Post by **b_weijenberg** » Mon Aug 11, 2008 1:27 pm

To control the KAKU plugin unit you need the RFXCOM transmitter.
Best is to use the new KAKU modules with automatic code system. These units have a dim level that can be set using Home Automation software.

If you order a receiver with an Ethernet interface you must have the model with 2 internal COM ports if you want to use the transmitter too.

Post by **KolNedra** » Mon Aug 11, 2008 5:24 pm

<blockquote id="quote">quote:<hr height="1" noshade id="quote">Originally posted by b_weijenberg
 To control the KAKU plugin unit you need the RFXCOM transmitter.
Best is to use the new KAKU modules with automatic code system. These units have a dim level that can be set using Home Automation software.

If you order a receiver with an Ethernet interface you must have the model with 2 internal COM ports if you want to use the transmitter too.
<hr height="1" noshade id="quote"></blockquote id="quote">
So if I want to receive signals from a AMST-606 (or AWST-6000) and at the same time send RF signals to a KAKU device (say AWMR-230) I need a RFXCOM with 2 internal com ports?

Just to be certain...

Post by **b_weijenberg** » Mon Aug 11, 2008 8:59 pm

That's true. For a receiver and a transmitter you need the Ethernet interface with 2 COM ports or 2 USB interfaces.

Post by **Harry** » Tue Sep 30, 2008 11:13 pm

what devicevalue gives the awst 606 (where can i see this value)

Post by **Willem4ever** » Wed Oct 01, 2008 8:11 am

<blockquote id="quote">quote:<hr height="1" noshade id="quote">Originally posted by Harry
 what devicevalue gives the awst 606 (where can i see this value)
<hr height="1" noshade id="quote"></blockquote id="quote">

249 for open and 9 for closed. (you can check the forum, this has been discussed before)