The procedure stalls at INFO:rooter:Logging in to U-Boot

If your (rooted) Toon doesn't do what it's supposed to, post here. Dutch allowed / Posten in 't Nederlands toegestaan.

Moderators: marcelr, TheHogNL, TerrorSource, Toonz

The procedure stalls at INFO:rooter:Logging in to U-Boot

Postby RdP » Sun Oct 20, 2019 8:04 pm

The procedure stalls at INFO:rooter:Logging in to U-Boot

Tried it many times and doublechecked the wiring.

All help is welcome!

Schermafbeelding 2019-10-20 om 20.52.47.png
Schermafbeelding 2019-10-20 om 20.52.47.png (185.6 KiB) Viewed 1853 times
Rien
User avatar
RdP
Advanced Member
Advanced Member
 
Posts: 983
Joined: May 2006
Location: Netherlands

Re: The procedure stalls at INFO:rooter:Logging in to U-Boot

Postby TheHogNL » Sun Oct 20, 2019 8:27 pm

Please read the readme carefully. Especially the part where it says "Then make sure the serial port on the Pi is enabled and the serial console is disabled using raspi_config and reboot if necessary. " And double check the wires.
Member of the Toon Software Collective
User avatar
TheHogNL
Forum Moderator
Forum Moderator
 
Posts: 1290
Joined: August 2017

Re: The procedure stalls at INFO:rooter:Logging in to U-Boot

Postby RdP » Sun Oct 20, 2019 8:29 pm

TheHogNL wrote:Please read the readme carefully. Especially the part where it says "Then make sure the serial port on the Pi is enabled and the serial console is disabled using raspi_config and reboot if necessary. " And double check the wires.


Hi,

I did !!!

Been trying for hours now and followed the instructions carefully
Rien
User avatar
RdP
Advanced Member
Advanced Member
 
Posts: 983
Joined: May 2006
Location: Netherlands

Re: The procedure stalls at INFO:rooter:Logging in to U-Boot

Postby TheHogNL » Sun Oct 20, 2019 8:56 pm

Ok then just try the manual rooting. You don't need the openocd which toonrooter does for you. Just use the simple uboot password for your toon explained in the manual rooting guide (here on the forum, somewhere on youtube and somewhere on another toon rooter guide on the internet).
My guess is that your TX cable just isn't working (our you are still double writing to the same console). Your RX is working fine (as the toonrooter can see your uboot version).
Member of the Toon Software Collective
User avatar
TheHogNL
Forum Moderator
Forum Moderator
 
Posts: 1290
Joined: August 2017

Re: The procedure stalls at INFO:rooter:Logging in to U-Boot

Postby RdP » Sun Oct 20, 2019 9:01 pm

TheHogNL wrote:Ok then just try the manual rooting. You don't need the openocd which toonrooter does for you. Just use the simple uboot password for your toon explained in the manual rooting guide (here on the forum, somewhere on youtube and somewhere on another toon rooter guide on the internet).
My guess is that your TX cable just isn't working (our you are still double writing to the same console). Your RX is working fine (as the toonrooter can see your uboot version).


What do you mean with "our you are still double writing to the same console)"?
Rien
User avatar
RdP
Advanced Member
Advanced Member
 
Posts: 983
Joined: May 2006
Location: Netherlands

Re: The procedure stalls at INFO:rooter:Logging in to U-Boot

Postby RdP » Sun Oct 20, 2019 9:03 pm

Toon Signal Pi
1 RTCK
2 TRST 24
3 GND 25
4 TCK 23
5 GND 20
6 TMS 22
7 SRST 18
8 TDI 19
9 Vt
10 TDO 21
11 RxD 8
12
13 TxD 10
14 GND 9

I used this wiring !!
Rien
User avatar
RdP
Advanced Member
Advanced Member
 
Posts: 983
Joined: May 2006
Location: Netherlands

Re: The procedure stalls at INFO:rooter:Logging in to U-Boot

Postby TheHogNL » Mon Oct 21, 2019 9:15 am

For your Toon only the 11 (RX), 13(TX) and 14(GND) is necessary.
Pleaes check again if you disabled the raspberry pi serial console and check the TX cable.
Member of the Toon Software Collective
User avatar
TheHogNL
Forum Moderator
Forum Moderator
 
Posts: 1290
Joined: August 2017


Return to Toon issues and support (Nederlands toegestaan)

Who is online

Users browsing this forum: No registered users and 1 guest